Quality cast iron radiator made in the grand Balmoral style. Manufactured using traditional casting techniques and guaranteed for 10 years.Height is 768mm from floor to top of radiator.
All radiators supplied fully assembled to maximum widths shown.
Distance from floor to centre of valve inlet/bush is 110mm.Key Points
* Height is for foot section from floor to top of radiator.
† All lengths approximate and include to bush ends - please allow 4% tolerance.
‡ Price for standard Black Primer finish, other finishes available at extra cost.
Standard finish to all cast iron radiators is a cellulose based BLACK primer.
The lead time from order placed to despatch for all radiator orders will be shown at checkout a. We will obviously ship sooner if order complete.
We can also supply this cast radiator ready painted/top coated in an authentic colour for only £3.75 + VAT per section.
The following exclusive colours are available:
As the radiators are hand assembled, all dimensions are approximate. We therefore advise that pipework should only be put in place once the radiator has been delivered.
All bush ends/caps will only be hand tight to allow customers to interchange if on a gravity fed heating system & will need fitting correctly when installed with PTFE etc.
Accessories & Bleed Valves
All Fittings (Valves, Wall stays, Shrouds etc) ordered will be placed in a bag or box placed on top of the top radiator. Air Vents/bleed valves will be in an SEALED ORANGE BAG with a bright yellow sticker stating 'Bleed Valves Enclosed'.If you are only receiving bleed valves these will be placed in the SEALED ORANGE BAG inside the top radiator. You MUST check it's content upon delivery & report any missing items immediately.
Guarantees & Conditons of Sale etc.
Guarantees & Conditions of Sale - Click Here!
All bush ends/caps for your cast iron radiators will only be hand tight to allow customers to interchange if on a gravity fed heating system and will need fitting correctly when installed.
A common cause of leaks is over tightening of the valve tails into the bush ends of the cast iron radiator. Over tightening will crack the bush. When fitting the valve tail in to the bush turn it finger tight then using a spanner turn it until there is only moderate resistance. Using a 4” spanner it is difficult to over tighten. A thread sealant must be applied to the radiator end caps and to the valve tail threads to get a water tight seal. LSX sealant available at all plumbers’ merchants is recommended. PTFE tape is an acceptable alternative. The torque from an 8” adjustable spanner will be sufficient to create a good seal.
All valves and air vents/bleed valves to be fitted with LSX sealant or PTFE tape.
No caustic/corrosive/acidic plumbing compounds or liquids are to be used on or in any part of our radiators, our valves or connections including aggressive flushing agents. If required, the system should be flushed with clean water only. The water in the system must be neutralised correctly following the use of any compounds etc if required using appropriate crystals or similar. If caustic and/or corrosive compounds (liquid or other) have been introduced into the system resulting in subsequent damage to seals/gaskets, any guarantee offered will be invalid. When a chemical cleanser is used it must be thoroughly flushed from the system. We recommend the use of Fernox F5 for power flushing and F1 rust inhibitor. Unlike other chemicals these products are not acid based and should not affect seals. After treatments the water should be checked for a neutral PH between 7 – 8. System design, flushing and dosing must be in accordance with BS 5449, 1990, BS EN 12828:2003 and BS 7593.
Following this procedure the system must be closed with a sufficient corrosion inhibitor suitable for the water quantity in your system. Dosing tools should be used to ensure the minimum correct levels of inhibitor are present at all times to prevent corrosion and should take into account the particular metals within the system. Appropriate inhibitor should be used in conjunction with manufacturer’s instructions and appropriate quantities must be used for the water content of the system.
We always advise you to wait for your cast iron radiators to be onsite before working out pipe work and pipe centres widths. This is because cast iron is not an exact product and because each radiator is hand assembled there will always be slight discrepancies as indicated on each radiator page in the lengths of same style & size radiators.
However, we appreciate that occasionally some prep work may need to be carried out prior to your order arriving onsite and that approximate pipe centre measurements may be required for first fix purposes.
Therefore, and strictly as a guide only, we would say for the approximate pipe centres for each cast iron radiator to add approx 90mm/3.5” to the overall length shown on the Specification tab. E.g. if the length indicated for a radiator is approximately 950mm then the approximate pipe centres will 1040mm & so on.
For the approximate measurement off the skirting board or wall if no skirting is used to the Pipe Centre we suggest half the depth of the cast iron radiator + 10mm as a minimum.
For the approximate ‘outside valve to outside valve measurement’ (the minimum measurement to be able to operate the valves freely) you should add approx 150mm/6.0” to the length indicated for each radiator in the Specification tab. E.g. if the length indicated for a radiator is 950mm then the approximate measurement from the outside of one valve to the outside of the opposite valve will be 1100mm.
PLEASE REMEMBER THAT THE ABOVE MEASUREMENTS SHOULD BE USED AS A GUIDE ONLY
All radiator pallet deliveries are made to kerb side only or nearest hard standing and are based on a 'Book In & Signed For' service (week days only). You will then be contacted by the delivery company 2-4 working days after despatch to organise delivery direct.
If you require a 'Dedicated Day' (working week day) for delivery to ensure you have help to hand you must indicate this in the message box at checkout. Please note that this may delay delivery slightly. This will still be a kerb side only or nearest hard standing service. For Saturday delivery, there will be an additional charge of £45.00 + vat on top of the standard delivery charge quoted.
Care should be taken when removing radiator(s) from the pallet on delivery. Radiators should be lifted off and NOT dragged/pulled as this will result in paintwork being damaged. When removed from the pallet, all radiators must be carried in an upright position to prevent damaged to joints.
If any items are deemed to be missing from any order, we must be contacted immediately (not longer than 2 days from receipt) via email. Failure to do so will result in additional items supplied being charged to the customer. We cannot be held responsible for any consequential costs incurred due to any shortfalls which have not been notified within the timescales above.
Prices for deliveries will be automatically calculated at checkout. Pallet Delivery Prices & Conditions - Click Here!
Review by: Vincent PageConsistent quality and service
This is the third balmoral we have purchased and everyone has been superb. We are slowly working our way through our home redecorating each room and replacing all the radiators with these high end products.
Comment by: allan
Very happy with my purchase, they look great and would definitely order from you again.
Review by: Anonymous2nd time for Balmoral
Having been so impressed with the previous purchase of an 8 section Balmoral radiator for our newly renovated bedroom suite, we returned to purchase a smaller version for the downstairs hall. The radiator arrived as promised with the same high grade finish as the first one. As we go through our home renovating each room we now intend to replace every current radiator with a Balmoral. Fabulous product faultless service
Review by: Peter woolley
Absolutely delighted with the radiator leeks are hallway nice and cosey and the service and help on purchase of the product from the staff was fantastic.
Review by: Janet Morgan
We are absolutely delighted with this radiator and the service we received was friendly and professional throughout. Would recommend to any-one.
Review by: K Taylor
Fantastic!!! Have a victorian house and the radiator finishes the room. A real focal point. Great service will certainly be ordering more
Review by: EHBeautiful
Absolutely stunning radiator! We are redeveloping a very old house and will certainly be ordering many more! Looks beautiful and the service was fab! Missed a VM from the company, when I eventually called them, they sent it out and it arrived the next day.
Review by: Sam HakimBalmoral 3 Column 768mm Cast Iron Radiator
Most beautiful ornamented Cast Iron Balmoral Radiator, Delivered in time as planned , , Great pleasure to do business with this company , Many thanks , * * * * *
Review by: JJBespoke Gun Metal cast iron radiators.
I hope you are well.
I just want to say the cast iron radiators look fantastic. They are amazing and I am so pleased with my purchase. I also want to thank you for helping me decide on my purchase - including colour- gun metal looks great. The king radiator is so impressive. Our house is almost done so I am hoping the radiators will be in place in three weeks.
By the way, I spoke to your colleague as I did not receive the wall hang and paint. It must have got lost in the post. Your colleague took my details and will be putting in the post again.
Thanks again and I hope to be purchasing from you again in the future, and will be recommending your company to my friends and family.
Review by: AnonymousStunning cast radiators
just wanted to say a huge thanks for the sorting us out.
All the radiators look fab, but the King is stunning to say the least & transforms our hallway.
The builders didn't thank me much though as it does weigh a little bit. I think I am still paying them in cups of tea & biscuits!!
Anyway, will be in touch soon for the door knobs.